Discussion:
[PATCH v4 0/6] arm: sunxi: IR support for A83T
(too old to reply)
Philipp Rossak
2018-01-29 15:58:04 UTC
Permalink
Raw Message
This patch series adds support for the sunxi A83T ir module and enhances
the sunxi-ir driver. Right now the base clock frequency for the ir driver
is a hard coded define and is set to 8 MHz.
This works for the most common ir receivers. On the Sinovoip Bananapi M3
the ir receiver needs, a 3 MHz base clock frequency to work without
problems with this driver.

This patch series adds support for an optinal property that makes it able
to override the default base clock frequency and enables the ir interface
on the a83t and the Bananapi M3.

In general this is a resend of the v3 Patchseries, but with collected acked-by
and reviewed-by and some typos fixed.

changes since v3:
* collecting all acks & reviewd by
* fixed typos

changes since v2:
* reorder cir pin (alphabetical)
* fix typo in documentation

changes since v1:
* fix typos, reword Documentation
* initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
* change dev_info() to dev_dbg()
* change naming to cir* in dts/dtsi
* Added acked Ackedi-by to related patch
* use whole memory block instead of registers needed + fix for h3/h5

changes since rfc:
* The property is now optinal. If the property is not available in
the dtb the driver uses the default base clock frequency.
* the driver prints out the the selected base clock frequency.
* changed devicetree property from base-clk-frequency to clock-frequency

Regards,
Philipp


Philipp Rossak (6):
media: rc: update sunxi-ir driver to get base clock frequency from
devicetree
media: dt: bindings: Update binding documentation for sunxi IR
controller
arm: dts: sun8i: a83t: Add the cir pin for the A83T
arm: dts: sun8i: a83t: Add support for the cir interface
arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
arm: dts: sun8i: h3-h8: ir register size should be the whole memory
block

Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 7 +++++++
arch/arm/boot/dts/sun8i-a83t.dtsi | 15 +++++++++++++++
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
5 files changed, 37 insertions(+), 9 deletions(-)
--
2.11.0
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Philipp Rossak
2018-01-29 15:58:05 UTC
Permalink
Raw Message
This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.

This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.

Signed-off-by: Philipp Rossak <***@gmail.com>
Reviewed-by: Andi Shyti <***@samsung.com>
Acked-by: Sean Young <***@mess.org>
---
drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
1 file changed, 11 insertions(+), 8 deletions(-)

diff --git a/drivers/media/rc/sunxi-cir.c b/drivers/media/rc/sunxi-cir.c
index 97f367b446c4..f500cea228a9 100644
--- a/drivers/media/rc/sunxi-cir.c
+++ b/drivers/media/rc/sunxi-cir.c
@@ -72,12 +72,8 @@
/* CIR_REG register idle threshold */
#define REG_CIR_ITHR(val) (((val) << 8) & (GENMASK(15, 8)))

-/* Required frequency for IR0 or IR1 clock in CIR mode */
+/* Required frequency for IR0 or IR1 clock in CIR mode (default) */
#define SUNXI_IR_BASE_CLK 8000000
-/* Frequency after IR internal divider */
-#define SUNXI_IR_CLK (SUNXI_IR_BASE_CLK / 64)
-/* Sample period in ns */
-#define SUNXI_IR_SAMPLE (1000000000ul / SUNXI_IR_CLK)
/* Noise threshold in samples */
#define SUNXI_IR_RXNOISE 1
/* Idle Threshold in samples */
@@ -122,7 +118,8 @@ static irqreturn_t sunxi_ir_irq(int irqno, void *dev_id)
/* for each bit in fifo */
dt = readb(ir->base + SUNXI_IR_RXFIFO_REG);
rawir.pulse = (dt & 0x80) != 0;
- rawir.duration = ((dt & 0x7f) + 1) * SUNXI_IR_SAMPLE;
+ rawir.duration = ((dt & 0x7f) + 1) *
+ ir->rc->rx_resolution;
ir_raw_event_store_with_filter(ir->rc, &rawir);
}
}
@@ -148,6 +145,7 @@ static int sunxi_ir_probe(struct platform_device *pdev)
struct device_node *dn = dev->of_node;
struct resource *res;
struct sunxi_ir *ir;
+ u32 b_clk_freq = SUNXI_IR_BASE_CLK;

ir = devm_kzalloc(dev, sizeof(struct sunxi_ir), GFP_KERNEL);
if (!ir)
@@ -172,6 +170,9 @@ static int sunxi_ir_probe(struct platform_device *pdev)
return PTR_ERR(ir->clk);
}

+ /* Base clock frequency (optional) */
+ of_property_read_u32(dn, "clock-frequency", &b_clk_freq);
+
/* Reset (optional) */
ir->rst = devm_reset_control_get_optional_exclusive(dev, NULL);
if (IS_ERR(ir->rst))
@@ -180,11 +181,12 @@ static int sunxi_ir_probe(struct platform_device *pdev)
if (ret)
return ret;

- ret = clk_set_rate(ir->clk, SUNXI_IR_BASE_CLK);
+ ret = clk_set_rate(ir->clk, b_clk_freq);
if (ret) {
dev_err(dev, "set ir base clock failed!\n");
goto exit_reset_assert;
}
+ dev_dbg(dev, "set base clock frequency to %d Hz.\n", b_clk_freq);

if (clk_prepare_enable(ir->apb_clk)) {
dev_err(dev, "try to enable apb_ir_clk failed\n");
@@ -225,7 +227,8 @@ static int sunxi_ir_probe(struct platform_device *pdev)
ir->rc->map_name = ir->map_name ?: RC_MAP_EMPTY;
ir->rc->dev.parent = dev;
ir->rc->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
- ir->rc->rx_resolution = SUNXI_IR_SAMPLE;
+ /* Frequency after IR internal divider with sample period in ns */
+ ir->rc->rx_resolution = (1000000000ul / (b_clk_freq / 64));
ir->rc->timeout = MS_TO_NS(SUNXI_IR_TIMEOUT);
ir->rc->driver_name = SUNXI_IR_DEV;
--
2.11.0
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Philipp Rossak
2018-01-29 15:58:06 UTC
Permalink
Raw Message
This patch updates documentation for Device-Tree bindings for sunxi IR
controller and adds the new optional property for the base clock
frequency.

Signed-off-by: Philipp Rossak <***@gmail.com>
Acked-by: Maxime Ripard <***@free-electrons.com>
Reviewed-by: Rob Herring <***@kernel.org>
---
Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt
index 91648c569b1e..278098987edb 100644
--- a/Documentation/devicetree/bindings/media/sunxi-ir.txt
+++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt
@@ -11,6 +11,8 @@ Required properties:
Optional properties:
- linux,rc-map-name: see rc.txt file in the same directory.
- resets : phandle + reset specifier pair
+- clock-frequency : IR Receiver clock frequency, in Hertz. Defaults to 8 MHz
+ if missing.

Example:

@@ -18,6 +20,7 @@ ir0: ***@1c21800 {
compatible = "allwinner,sun4i-a10-ir";
clocks = <&apb0_gates 6>, <&ir0_clk>;
clock-names = "apb", "ir";
+ clock-frequency = <3000000>;
resets = <&apb0_rst 1>;
interrupts = <0 5 1>;
reg = <0x01C21800 0x40>;
--
2.11.0
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Philipp Rossak
2018-01-29 15:58:07 UTC
Permalink
Raw Message
The CIR Pin of the A83T is located at PL12.

Signed-off-by: Philipp Rossak <***@gmail.com>
---
arch/arm/boot/dts/sun8i-a83t.dtsi | 5 +++++
1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index de5119a2a91c..06e96db7c41a 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -617,6 +617,11 @@
interrupt-controller;
#interrupt-cells = <3>;

+ cir_pins: cir-***@0 {
+ pins = "PL12";
+ function = "s_cir_rx";
+ };
+
r_rsb_pins: r-rsb-pins {
pins = "PL0", "PL1";
function = "s_rsb";
--
2.11.0
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Maxime Ripard
2018-01-30 08:38:32 UTC
Permalink
Raw Message
hi,
Post by Philipp Rossak
The CIR Pin of the A83T is located at PL12.
---
arch/arm/boot/dts/sun8i-a83t.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index de5119a2a91c..06e96db7c41a 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -617,6 +617,11 @@
interrupt-controller;
#interrupt-cells = <3>;
+ pins = "PL12";
+ function = "s_cir_rx";
+ };
+
Sorry for not noticing this earlier, but this should be r_cir_pin, and
you should drop the unit-address that generates a dtc warning.

Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Philipp Rossak
2018-01-29 15:58:08 UTC
Permalink
Raw Message
The cir interface is like on the H3 located at 0x01f02000 and is exactly
the same. This patch adds support for the ir interface on the A83T.

Signed-off-by: Philipp Rossak <***@gmail.com>
---
arch/arm/boot/dts/sun8i-a83t.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index 06e96db7c41a..ddc0d592107f 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -605,6 +605,16 @@
#reset-cells = <1>;
};

+ cir: ***@01f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
+ clock-names = "apb", "ir";
+ resets = <&r_ccu RST_APB0_IR>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x400>;
+ status = "disabled";
+ };
+
r_pio: ***@1f02c00 {
compatible = "allwinner,sun8i-a83t-r-pinctrl";
reg = <0x01f02c00 0x400>;
--
2.11.0
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Maxime Ripard
2018-01-30 08:39:27 UTC
Permalink
Raw Message
hi,
Post by Philipp Rossak
The cir interface is like on the H3 located at 0x01f02000 and is exactly
the same. This patch adds support for the ir interface on the A83T.
---
arch/arm/boot/dts/sun8i-a83t.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index 06e96db7c41a..ddc0d592107f 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -605,6 +605,16 @@
#reset-cells = <1>;
};
+ compatible = "allwinner,sun5i-a13-ir";
You should have an A83t compatible there first.

Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Philipp Rossak
2018-01-29 15:58:09 UTC
Permalink
Raw Message
The Bananapi M3 has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Unlike the other IR receivers this one needs a base clock frequency
of 3000000 Hz (3 MHz), to be able to work.

Signed-off-by: Philipp Rossak <***@gmail.com>
Acked-by: Chen-Yu Tsai <***@csie.org>
---
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 7 +++++++
1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index 6550bf0e594b..ffc6445fd281 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -82,6 +82,13 @@
};
};

+&cir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cir_pins>;
+ clock-frequency = <3000000>;
+ status = "okay";
+};
+
&ehci0 {
/* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
status = "okay";
--
2.11.0
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Maxime Ripard
2018-01-30 08:40:16 UTC
Permalink
Raw Message
Post by Philipp Rossak
The Bananapi M3 has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Unlike the other IR receivers this one needs a base clock frequency
of 3000000 Hz (3 MHz), to be able to work.
---
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index 6550bf0e594b..ffc6445fd281 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -82,6 +82,13 @@
};
};
+&cir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cir_pins>;
If this is the only muxing option (like your node name suggests), you
can put it directly in the DTSI to remove boilerplate from all the
DTS.

Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Philipp Rossak
2018-01-29 15:58:10 UTC
Permalink
Raw Message
The size of the register should be the size of the whole memory block,
not just the registers, that are needed.

Signed-off-by: Philipp Rossak <***@gmail.com>
---
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 8d40c00d64bb..a9caeda4a574 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -674,7 +674,7 @@
clock-names = "apb", "ir";
resets = <&r_ccu RST_APB0_IR>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
+ reg = <0x01f02000 0x400>;
status = "disabled";
};
--
2.11.0
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Loading...