Discussion:
[PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
(too old to reply)
Icenowy Zheng
2018-02-06 13:16:47 UTC
Permalink
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.

It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.

Signed-off-by: Icenowy Zheng <***@aosc.io>
---
Changes in v4:
- Use SPDX license identifier.

Changes in v3:
- Add comments about Vbus problem in &usbphy node.

Changes in v2:
- Use high active SD card detect on the production batch.

arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126 +++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..d5a17e6e8b0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..e2ee65a5bf92
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <***@aosc.io>
+ *
+ * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
+ * Copyright (C) 2016 Chen-Yu Tsai <***@csie.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Zero";
+ compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+
+ pwr_led {
+ label = "bananapi-m2-zero:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ /*
+ * On the production batch of this board the card detect GPIO is
+ * high active (card inserted), although on the early samples it's
+ * low active.
+ */
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <&reg_vcc3v3>;
+ vqmmc-supply = <&reg_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: ***@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ /*
+ * There're two micro-USB connectors, one is power-only and another is
+ * OTG. The Vbus of these two connectors are connected together, so
+ * the external USB device will be powered just by the power input
+ * from the power-only USB port.
+ */
+ status = "okay";
+};
--
2.15.1
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Icenowy Zheng
2018-02-08 09:15:35 UTC
Permalink
在 2018-02-08 17:00,Maxime Ripard 写道:
Post by Icenowy Zheng
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
---
- Use SPDX license identifier.
- Add comments about Vbus problem in &usbphy node.
- Use high active SD card detect on the production batch.
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
+++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..d5a17e6e8b0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..e2ee65a5bf92
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,126 @@
+/*
+ *
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
Sorry to be a bit picky about this, but this should be your very first
line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
example.
I think it's also OK here, see
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
Thanks!
Maxime
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Jernej Škrabec
2018-02-08 09:28:32 UTC
Permalink
Post by Icenowy Zheng
在 2018-02-08 17:00,Maxime Ripard 写道:
Post by Icenowy Zheng
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
---
- Use SPDX license identifier.
- Add comments about Vbus problem in &usbphy node.
- Use high active SD card detect on the production batch.
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
+++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..d5a17e6e8b0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..e2ee65a5bf92
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,126 @@
+/*
+ *
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
Sorry to be a bit picky about this, but this should be your very first
line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
example.
I think it's also OK here, see
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
Lincesing rules [1] says it should be in first possible line which can contain
comment.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
Documentation/process/license-rules.rst#n57
Post by Icenowy Zheng
Thanks!
Maxime
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group. To unsubscribe from this group and stop receiving
For more options, visit https://groups.google.com/d/optout.
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Chen-Yu Tsai
2018-02-08 09:41:06 UTC
Permalink
Post by Jernej Škrabec
Post by Icenowy Zheng
在 2018-02-08 17:00,Maxime Ripard 写道:
Post by Icenowy Zheng
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
---
- Use SPDX license identifier.
- Add comments about Vbus problem in &usbphy node.
- Use high active SD card detect on the production batch.
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
+++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..d5a17e6e8b0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..e2ee65a5bf92
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,126 @@
+/*
+ *
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
Sorry to be a bit picky about this, but this should be your very first
line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
example.
I think it's also OK here, see
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
Lincesing rules [1] says it should be in first possible line which can contain
comment.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
Documentation/process/license-rules.rst#n57
I confess I only read the license line rule some time after I posted that
patch.

ChenYu
Post by Jernej Škrabec
Post by Icenowy Zheng
Thanks!
Maxime
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group. To unsubscribe from this group and stop receiving
For more options, visit https://groups.google.com/d/optout.
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+***@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Loading...